How to install wallpaper on walls is a skill that seems more difficult than it actually is. You can master these steps with the right tools and a few exercises. As with any craft, beginners can make mistakes, but by choosing the right paper type and pattern, you can correct or avoid them.

It is best to avoid expensive fingerprint paper, which can be stained with a touch of water, easily torn and permanently show wrinkles. They are washable, if you put excess glue, you can clean them with a damp sponge. They can also be lengthened to help straighten stitches or allow you to peel off and reposition strips that don’t fit.

Materials For Installing Wallpaper

The important things you need to install the wallpaper are:

Wallpaper

To make sure you buy enough wallpaper, measure the width and height of all the walls, then use a wallpaper calculator (which you can find online or download as an app). sites.

Glue Wallpaper

Wallpaper application brush

Choose one with a handle in the middle to make it easier to fit into the finished pasta container.

Plumb Measurement Tool

Knife and scissors for cutting wallpaper.

Using a knife is easier, but scissors are better for wallpaper strips that won’t cut because they get wet from the glue. You also need scissors to cut the paper from the rolls.

Measuring Tape

Pensil

Clean Cloth

Wallpaper table

For those of you who want to install your own wallpaper, let’s see how to install the following wall wallpaper!

Tidying the Walls

First, make sure the walls are flat. You have to fix the bumps and holes in the walls. Remove the nails, hooks or screws with pliers. Fill the large holes with caulk and sand the holes before applying the wallpaper so that it does not cause bulges under the strip.

Next, make sure all the walls are clean, dry, and free of dirt and cobwebs. If there are “problem areas” like moisture, make sure the problem is resolved before applying the wallpaper.

Measurement Wall Wallpaper

Pick an “easy” wall area (that doesn’t have a switch) to start with. If possible, start in an area that may not be as obvious as you are done. This way, if the first strip or two of wallpaper have some mistakes, it won’t be a problem.

Measure the length of the wall to be wallpaper, then add about 20cm. Unroll the paper on the sticky table, then using a tape measure and pencil, make a mark on the back of the paper where it should be cut. Fold the paper and make sure it is aligned around the edges, then cut the first strip.

Installing the wallpaper on the wall

Now that you have the first piece cut out, it’s time to attach it to the wall. Give the walls a generous coat of glue (put the roll on the wall first and mark how far the wall should stick), then stick a small sheet of paper in the top corner first.

Apply the strip to the top of the wall, then gently spread it against the wall with a gentle wash with a clean cloth. Flatten from the center of the paper to the edges. Remember to smooth it gently so that the paper does not wrinkle. Once it’s in place properly, use a cloth to smooth the edges

Then use the cloth to push the paper as far as possible into the space where it meets the ceiling and edges, so that a thin line is formed to mark where you will cut off the excess wallpaper.

Installing wallpaper on wall corners

The trick with the corners is to focus on the wall first, then focus on moving the second sheet of paper to the next wall. Follow the edges and patterns as before, then wipe your fabric gently in the corners. Do not apply too much pressure on the top and bottom corners to prevent the paper from wrinkling.

Once the paper fills the corner, carefully place the paper on the second wall. Using scissors, cut the paper at the top of the corner that meets the ceiling. This will help you fold the paper on the second wall.

Make another cut at the bottom of the strip where the paper meets the edge corner, then focus on smoothing the paper along the wall from the corner to the edge. Make sure the paper does not come off the old strip. If so, carefully lift it up, replace it, and then flatten it against the wall.

Wallpaper installation in difficult wall areas

Sticking wallpaper on the part of the wall where there are switches and sockets is not so easy. Hang the wallpaper as before, but don’t stain the strip too much. Feel where the plug or switch is under the paper, then poke a small hole with a pair of scissors. Carefully cut the paper, moving it from the center of the plug toward the edge, until you can press it against the wall and the plug or switch opens fully.

Using a cloth, gently flatten the paper around the edge of the plug / switch, then make the final cut with a pair of scissors. Flatten the rest of the strip towards the switch / socket.

Those are the ways to put wallpaper on the wall.

LEAVE A REPLY

Please enter your comment!
Please enter your name here